1. Construction lifts can be safely carried by the carrier, mainly because it is equipped with anti-fall safety device, greatly improving the safety factor. At present, the construction site is widely used in the rack and pinion drive dual-use construction of the lift is generally equipped with a gear cone-shaped progressive anti-fall safety device.

The main components of the gear-type tapered progressive-type anti-fall safety device are gears, centrifugal speed limiters and tapered drum brakes.

The working principle of the gear cone-shaped progressive anti-fall safety device is that when the operating speed of the protection target (construction lift cage) reaches the calibrated speed, the centrifugal speed limiter is displaced (equivalent to the pawl ), The taper drum (rather ratchet) moves to the brake belt, contacts and produces the braking torque, and the disc spring group is compressed to measure the amount of compression, by calculating the braking distance at which the rated braking load can be determined..

2 Pinion and Cone Progressive Safety Device SAJ40, Construction Hoist Spare parts Safety Device

SAJ serials pinion and cone progressive safety device is the most important safety device in the pinion and rack builder’s hoist, which can prevent the cage running over speed, and effectively reduce the cage dropping accident. Is the most important safety equipment on the rack and pinion construction building elevator. It can limit the cage speeding downward, so can prevent the cage falling accident.

The safety device is the most optimal fall arrestor, which restricts the excessive downward movement of the cage and prevents cage falling accidents, makes the device absolutely reliable. It is anti-dropping protection device, and in case the hoist cage falls, it may ensure safety and reliability of personnel and material .

Aplicativo

occasions: SAJ serials pinion and cone progressive safety devices are used in wire rope hoist ,hydraulic hoist and rack and pinion hoist. The following introduces the applications of all kinds of series of safety device :SAJ02-1.2 and SAJ08-1.2 safety device mainly used in small rack and pinion hoist ,such as wind power tower hoist ;SAJ30-0.5is used in ultra-low speed of safety device ,such as lifting platforms; Customers can choose the type of saft devices according to hoist rated lifting speed and load. Tripping Speed of safety devices is no more than 0.4m/s of the hoist’s rated speed. The production of this product conforms to EN12159, EN12158, EN1495, GB26557-2011, JG121-2000.The reason can be safely lift construction manned loading operation, mainly due to its anti-fall safety device is equipped, greatly improving the safety factor. At present, the construction site is widely used rack and pinion construction hoist people generally equipped with dual-use goods is tapered drum gear progressive anti-fall safety device.

3.Pinion and Cone Progressive Safety Device SAJ40, Construction Hoist Spare parts Safety Device

4 Cautions

1. During safety device operation, Lubricating grease should be filled into the oilcup placed on the pinion shaft end once a week, the grease type should be No.2 calcic-base one based on GB491-87. Furthermore, when using SAJ40-2.0,SAJ50-1.2, SAJ50-2.0 or SAJ60-2.0 safety device, gease should be filled through6oil hole on support shaft edge to lubricate transmission pinion bears.

2. No matter the usage status, the safety device should be inspected annually. Onlyin valid qualified inspection period could the safety device be put into used.

3. The user is not allowed to open lead seal of safety device without permission, otherwise the manufacturer would not take any responsibilities for any accidents.

4. The product guarantee period is one year.

5. Manufacturer only takes the responsibility of transmission pinions’ quality. The bear wearing and working noise caused by improper installation and operation are not guaranteed to be serviced by manufacturer.

6. Special attention: without permission, the user could not adjust the location of position limited structure and ping 4 in fig.2 of safety device. After safe device taking action during hoist operation the activation causes should be investigated, and the safety device could be reused only after all the faults are fixed and safety device recovered based on the above instructions. It is strictly forbidden that safety device keep operation without correct recovery after action.

Pinion and Cone Progressive Safety Device SAJ40, Construction Hoist Spare parts Safety Device

5.Recovery of the safety device:

Pinion and Cone Progressive Safety Device SAJ40, Construction Hoist Spare parts Safety Device. Except for drop test, if the safety device braking happens, before recovery operation the safety device action reason should firstly be investigated, at the same time the followings should be identified.
1) Whether the brake works normally.
2) Whether the turbine pair and the coupling work normally.
3) Whether the guide rolling wheel and support rolling wheels work normally.
4) Whether pinion and the rack work normally.
5) Whether position limited structure on the safety device work normally (when inspection the electric circuit should be switched off).

Our Services

Pinion and Cone Progressive Safety Device SAJ40, Construction Hoist Spare parts Safety Device

1.24-hours online consulation service is avaliable here.
Once you have any questions, just contact us and our professional staff will reply very quickly.

2. Market information also will be provided.
Since we are an experienced supplier of hoist parts, the market information about hoist and hoist parts will be offered as long as you contact us and ask for it.

Quick Details

Place of Origin: Shanghai, China (Mainland)
Color:Red\Orange
Hoisting Speed: 36 M/MIN
Rated Loading Capacity(kg): 2x2000KG
Max Lifting Height: 250M
Loder Weight: 2 Ton
Applicable Models: Low-Speed Construction Hoist
Material: Steel
Warranty: 12 Months
Certification: ISO9001:2008
Name: Safety Device SAJ40, Hoist Safe